A thermal Activation Device, also called a thermal activation generator, is an automatic unique thermal detection and activation device that allows to detection of a fire, om het brandblusapparaat te activeren, het werkt mee alle brandblusinstallaties.
This device is a visible installation type, when the environment temperature arrives at the device’s rated temperature, after waiting a time delay of 15 tot 99 seconden, it can cause an instantaneous current to the fire extinguishing units to make them work.
Adding a magnetic switch at the wire-connection box can help transmit the activation signal feedback to the fire extinguishing system. inside the wire-connection box is accompanied by an indicator, and circuit board, when the device has voltage output, het indicatielampje licht op, and a photoelectric switch can help transmit the signal to the fire extinguishing systems.
Productparameters::
productnaam: thermisch activeringsapparaat:, thermische activeringsgenerator, kortom is “THEN, LABEL, TG”. “THEN” is een afkorting voor “Thermisch activeringsapparaat”, “LABEL” is een afkorting voor “Thermische activering Generator”, en “TG” is een afkorting voor “Thermal Generator”.
Product Dimension: (65*139 millimeter).
Werkingstemperatuur:: -60 tot +60 graden Celsius.
Rated Activation Temperature: 45±5℃, 70±5℃, 93±5℃, en 110±5℃.
Compatibiliteit: aërosol, schuim, waternevel, droge chemische stof, and gas system.
Werkend principe: Utilizing the principle of electromagnetic induction to generate current and activate the fire extinguisher.
This thermal activation generator is an accessory of fire suppression systems of aerosol fire extinguishers and dry chemical fire suppression units.
The Thermal activation generator not only takes the role of fire detection element but also takes the role of starting the fire suppression systems, het heeft onderstaande functies:
It can be used as a standard thermal detection element with a fire temperature reading.
It can be connected to the standard fire control panel of a fire alarm system by use of an additional electronic box.
Complied with an explosion-proof junction box TAD can be used in a safety sensor D3 for application in hazardous areas.
Het apparaat TAD is zeer geschikt voor autonome bediening in een brandblussysteem.
Geen externe voeding nodig.
Het kan werken met brandalarmsystemen om te werken voor branddetectie.
It can operate separately, met andere woorden, it is also a stand-alone detection accessory for fire protection.
Work alone with fire suppression system generators without any outer power supply, en kan ook werken met brandmeldinstallaties, below are its partners:
Aerosol brandblusser en systemen.
Droog chemisch poeder brandblusser en systemen.
Fm200 brandblussystemen.
Kooldioxide brandblussystemen.
NOVEC 1230 or FK5-1-1-2 fire protection systems.
Inert gas IG541 brandbeveiligingssystemen.
Brandblussystemen van schuim.
Watermistbestrijdingssystemen.
Andere relatieve brandblussystemen.
When the device detects that the ambient temperature has reached the activation temperature, the thermosensitive head melts, and the internal magnetic components move under the pressure of the compression spring. The inductance coil ignites the current to ignite thefire extinguisher generator.
Please note the following:
Volume protected by one device shall not exceed 18 Kubieke meters.
The thermal activation device should be installed in a protected area 50 tot 200 mm below the ceiling.
The thermal activation generator is suitable for application in hazardous areas of 2ExeIIT6 category.
Its maximum relative humidity is 98% (niet-condenserend).
The startup temperature of this device can also be customized specifically for customers.
Na installatie, the safety pin of the device should be promptly removed.
Voor meer technische details hierover Thermisch activeringsapparaat, Alsjeblieft inquire from usand we will respond to you within 24 uur.
Aanvraagformulier ( we zullen terug te krijgen u zo spoedig mogelijk )
